How to Find and Use Your Main Water Shut-Off
Short answer: The main water shut-off is usually where the water line enters the house: on a garage wall, in the crawlspace on the street side, in a basement or near the water heater. A round wheel valve closes clockwise; a lever valve closes with a quarter turn until the handle sits across the pipe. Test it before you need it.
In a leak, the first two minutes decide whether you need a plumber or a plumber plus a restoration crew. Find your shut-off now, while nothing is leaking.
Kent WA Plumbers is an independent referral service, not a plumbing company. Your request is passed to an independent, locally licensed plumbing company. Disclosure
Phone line coming soon. Email us now.
Updated · Written by the Kent WA Plumbers editorial team (a referral service, not a licensed plumber) · Fact-checked against the public sources linked on this page · How we research guides
Where is the main shut-off in Kent-area homes?
Your main shut-off is almost always on the line where water enters the house from the meter, usually on the side of the house facing the street. In this area, look in this order:
- Garage: on the wall shared with the house or facing the street, often low, sometimes near the water heater.
- Crawlspace: common in Kent's ramblers and split-levels. Look just inside the foundation wall nearest the street. A flashlight and a quick trip in now beats a first trip in during a flood.
- Basement or utility room: where the pipe comes through the foundation.
- Near the water heater: the cold inlet valve on top of the heater only isolates the heater. Keep looking for the main.
- Outside: some homes have a valve in a small box near the foundation or in a hose-bib-like spot on the outside wall.
Can't find it? Check your home inspection report from when you bought the house. It often has a photo.
How do you close the main shut-off?
- Lever (ball) valve: turn the handle a quarter turn until it sits across the pipe. Open is in line with the pipe.
- Round wheel (gate or globe) valve: turn clockwise until snug, which may take several turns. Don't crank on it.
After closing it, open a faucet on the lowest floor to drain pressure, then switch the water heater to pilot or vacation (gas) or turn off its breaker (electric).
How often should you test it?
Valves that sit untouched for years seize. Once in spring and once in fall, close the main, check that a faucet stops running, then reopen it fully. If it's stiff, weeping at the stem, or doesn't stop the water, schedule a replacement during regular hours. That costs far less than discovering the problem during a burst pipe.
Why should you label it?
Tie a bright tag on the valve and tell everyone in the house, including teenagers, house-sitters and tenants, where it is and which way to turn it. Put a photo of it in your phone.
Can you use the valve at the meter?
The water meter usually sits in a concrete box near the street or sidewalk. The City of Kent says its responsibility runs from the main in the street to the meter, so the meter and its valve belong to your water provider. In an emergency, the valve on the street side of the meter can be closed with a meter key from a hardware store. Lift the lid carefully, watch for standing water and spiders, and don't force a stuck valve. If water is bubbling up in the street or at the meter itself, that's a utility problem: call your water provider. In Kent that may be the City of Kent, Soos Creek Water & Sewer, Lake Meridian Water District or Highline Water District, depending on your address.
Which upgrades are worth asking a plumber about?
- Replace an old gate valve with a quarter-turn ball valve at the main. It's quick to close and less likely to seize.
- Add individual shut-offs at fixtures that don't have them.
- Automatic leak shut-off valves, which close the main when a sensor detects water. Some insurers offer discounts for them.
- A pressure-reducing valve and expansion tank if your pressure is high, which strains every fixture and the water heater.
Need a valve replaced or a leak fixed? Email hello@kentwaplumbers.com to reach an independent local licensed plumber.
Sources
- City of Kent, "Who Do I Call…" (water responsibility main-to-meter; water providers within Kent)
- Highline Water District, Your District (serves portions of Kent)
Questions people ask
Where is the main water shut-off in a house?
Usually where the water line enters the house: on a garage wall, in the crawlspace near the foundation wall facing the street, in a basement, or near the water heater. Follow the line from the street side of the house.
Which way do I turn the water shut-off valve?
A round wheel (gate or globe) valve closes clockwise, "righty-tighty." A lever (ball) valve closes with a quarter turn, until the handle sits across the pipe.
Can I turn off the water at the meter?
The valve at the meter is the utility's, and opening the box takes care. In a real emergency many homeowners close it with a meter key, but the safest plan is a working house-side shut-off. If your house valve is missing or broken, have a plumber install one.
What if my shut-off valve is stuck?
Don't force it with a long wrench; old gate valves can snap. Use the meter valve in an emergency, then have a plumber replace the house valve with a quarter-turn ball valve.
Should I turn off the water heater when the main is off?
If the main will be off for more than a short time, set a gas water heater to pilot or vacation, or switch off the breaker for an electric heater, so it doesn't run with no water coming in.