Toilet, Faucet and Fixture Repair in Kent, WA
Short answer: Most toilet and faucet problems can wait for a regular-hours visit, which costs less. A running toilet is usually a worn flapper, a fill valve set too high or a tangled chain. Toilet repairs run $100 to $300 (HomeGuide) or $150 to $375 (Angi, 2026). An overflow that won't stop after you close the supply valve is urgent.
Most toilet and faucet problems aren't emergencies, which means you can book a regular-hours visit and pay less. Email hello@kentwaplumbers.com to reach a local licensed plumber, or try the simple fixes below first.
Kent WA Plumbers is an independent referral service, not a plumbing company. Your request is passed to an independent, locally licensed plumbing company. Disclosure
Phone line coming soon. Email us now.
Updated · Written by the Kent WA Plumbers editorial team (a referral service, not a licensed plumber) · Fact-checked against the public sources linked on this page · How we research guides
Which toilet and faucet problems can wait?
| Problem | Urgency | First step |
|---|---|---|
| Toilet overflowing | Now | Close the supply valve behind the toilet (clockwise). Lift the tank lid and push the flapper down |
| Water around the toilet base | Soon: a failed wax seal can rot the subfloor | Stop using that toilet; photograph the floor |
| Toilet runs or refills on its own | Can wait | Food-coloring test for a leaky flapper |
| Dripping faucet | Can wait | Close the valves under the sink if it's bad |
| Low flow at one faucet | Can wait | Unscrew and clean the aerator |
| Leak under the sink | Soon | Close the valves, put a bucket under it, and check the supply hoses and drain slip nuts |
Which fixes can most homeowners do?
- Replace a toilet flapper. Shut off the supply valve, flush to empty the tank, unhook the old flapper and clip in a matching one. Take the old one to the hardware store.
- Adjust the fill valve so the water stops about an inch below the top of the overflow tube.
- Clean a faucet aerator clogged with grit, which is common after water-main work in the street.
- Swap a braided supply hose that's bulging or rusty at the ends. Many plumbers suggest replacing these on a schedule.
Stop and call if a shut-off valve won't close fully, starts leaking when you turn it, or the toilet rocks on the floor. Old multi-turn valves often seize after years without use, and forcing them can break them.
Which jobs should a plumber handle?
- Toilet replacement and flange repair. A soft or rotted floor under the toilet needs repair before a new toilet goes in. In Kent's many crawlspace homes, the plumber can often inspect the subfloor from below.
- Shower and tub valves. Replacing a valve body means opening the wall, and modern valves include anti-scald protection.
- Kitchen faucet and disposal swaps where corroded connections or a tight cabinet make the job harder than it looks.
- Replacing old shut-off valves with quarter-turn valves, so the next emergency is easy to stop.
- Anything involving gas, such as gas water heaters and ranges. In Washington, plumbing work must be done by a state-certified plumber.
How do you choose new fixtures?
- Toilets: look for the EPA WaterSense label (1.28 gallons per flush or less). Check the "rough-in" distance from the wall to the floor bolts, usually 12 inches, before buying.
- Faucets: count the holes in your sink or counter, and choose a model whose cartridges are easy to find locally.
- Showerheads: WaterSense-labeled models use less water and therefore less hot water, which lowers energy use too.
If you buy the fixture yourself, ask whether the plumber warranties labor on customer-supplied parts. Policies vary.
How much does toilet and faucet repair cost?
- Toilet repair: $100–$300 (HomeGuide); $150–$375 (Angi, 2026)
- Toilet installation: $250–$750 (HomeGuide)
- Faucet installation: $120–$300 (HomeGuide)
- Shower valve installation: $225–$575 (HomeGuide)
Seattle-area labor typically runs above national averages. Booking several small jobs into one visit is a good way to spread the trip charge. See the Kent plumbing cost guide.
Leak, clog or no hot water?
Email hello@kentwaplumbers.comPhone line coming soon. Email us now. Write to hello@kentwaplumbers.com with your ZIP code and what is wrong. Your request is passed to an independent, locally licensed Kent-area plumbing company. Ask for the company name, its L&I license number and the price before any work starts.
Sources
- U.S. EPA WaterSense, Residential toilets
- HomeGuide, Plumbing price list; Angi, Emergency plumber cost (2026)
- Washington L&I, Plumber certification
Questions people ask
How much does toilet repair cost?
HomeGuide lists toilet repairs at $100 to $300 and Angi's 2026 range is $150 to $375. Installing a new toilet runs about $250 to $750 in labor and parts (HomeGuide), depending on the toilet you choose and the condition of the flange underneath.
Why does my toilet keep running?
Usually a worn flapper that lets water seep into the bowl, a fill valve set too high so water spills into the overflow tube, or a chain that's tangled or too short. All three are inexpensive parts.
Is a dripping faucet worth fixing?
Yes. A steady drip wastes water around the clock and the worn part (a cartridge, washer or O-ring) usually costs little. Fixing it during regular hours keeps the bill low.
What is a WaterSense toilet?
A toilet certified by the EPA's WaterSense program to use no more than 1.28 gallons per flush while still meeting performance tests. Older toilets used much more.
When is a toilet problem urgent?
When it overflows and won't stop after you close the supply valve, when sewage backs up into the bowl or tub, or when water is leaking from the base onto the floor. Turn off the valve behind the toilet and call.