Repiping Older Homes in Kent, WA

Short answer: Repiping makes sense when supply pipes leak in more than one place, the water runs rusty, or the house has failing galvanized or polybutylene pipe, which was installed from roughly the late 1970s to the mid-1990s. Angi's 2026 data puts the national average repipe at $7,500, with most projects between $1,500 and $15,000. Most repipes today use PEX.

If your supply pipes keep springing leaks or the water runs rusty, patching one spot at a time can cost more than replacing them. Email hello@kentwaplumbers.com to reach a local licensed plumber for an honest repair-or-repipe assessment.

Email us How this works

Kent WA Plumbers is an independent referral service, not a plumbing company. Your request is passed to an independent, locally licensed plumbing company. Disclosure

Phone line coming soon. Email us now.

Updated · Written by the Kent WA Plumbers editorial team (a referral service, not a licensed plumber) · Fact-checked against the public sources linked on this page · How we research guides

How do you know your pipes, not just one leak, are the problem?

Which pipes did Kent homes use in each era?

The median home in Kent was built in 1985, about 39% were built before 1980, and only about 22% are from 2000 or later (Census ACS 2020–2024). That spread matters, because supply-pipe materials changed over the decades:

BuiltCommon supply pipeWhat to watch for
Before ~1960Galvanized steelRust builds up inside and narrows the pipe; leaks start at threaded joints
1960s–1970sCopper, some galvanizedCopper is generally durable; check older joints and any galvanized sections left from earlier repairs
Late 1970s – mid-1990sPolybutylene in some homes, copper in othersPB fittings were the subject of a national class-action settlement after widespread leaks
Late 1990s onCopper, CPVC, then PEXUsually fine; failures tend to be fittings or freeze damage

Not every house from a given decade has the problem pipe. A plumber can tell in minutes by looking at the pipe where it enters the water heater and in the crawlspace.

Repair or repipe?

A single leak in otherwise healthy copper or PEX is a repair. Repiping makes sense when the material itself is failing (galvanized that's corroded through, or polybutylene) and leaks keep moving to new spots. It's also worth pricing a repipe if you're already opening walls for a remodel. A partial repipe of the worst runs, such as the main trunk line or one bathroom group, is a legitimate middle option. Ask the plumber to price both.

What does a repipe involve?

  1. Walkthrough and quote: fixture count, route plan, pipe material, access holes, permit and patching scope.
  2. Permit: a repipe is a significant alteration, so expect a plumbing permit and inspection.
  3. New lines run to each fixture. In Kent's many crawlspace homes, much of the work can be done from below, with fewer wall openings than a slab home.
  4. Cut-over and testing: fixtures connected and the new system pressure-tested.
  5. Inspection, then patching: wall openings closed after the inspector signs off.

Ask whether new shut-off valves, a new main shut-off, and an expansion tank or pressure-reducing valve are included. They're cheap to add during a repipe.

Is PEX or copper better?

How much does repiping cost?

Angi's 2026 data puts the national average repipe at $7,500, with most projects between $1,500 and $15,000. Labor is about 70% of the bill. HomeGuide lists new plumbing pipes at $2,280–$5,120 for typical projects. Size, story count, fixture count, access and finish repairs drive the range, and Seattle-area labor typically runs above national averages. Compare quotes that list the pipe material, fixture count, permit, patching and warranty. See the Kent plumbing cost guide.

Leak, clog or no hot water?

Email hello@kentwaplumbers.com

Phone line coming soon. Email us now. Write to hello@kentwaplumbers.com with your ZIP code and what is wrong. Your request is passed to an independent, locally licensed Kent-area plumbing company. Ask for the company name, its L&I license number and the price before any work starts.

Sources

Questions people ask

How do I know if I have polybutylene pipe?

Polybutylene (PB) is a flexible plastic supply pipe, usually gray but sometimes black or blue, often stamped "PB2110". It was installed in homes from roughly the late 1970s to the mid-1990s, often with gray or white plastic fittings and metal crimp rings. Check where pipes enter the water heater, under sinks, and in the crawlspace.

How much does it cost to repipe a house?

Angi's 2026 data puts the national average at $7,500, with most homeowners spending $1,500 to $15,000 depending on home size, number of fixtures, pipe material and access. Drywall repair and permits are often extra. Seattle-area labor typically runs above national averages.

Is PEX or copper better for repiping?

Both are code-approved. PEX is flexible, faster to install with fewer wall openings, resists freeze splitting better, and costs less. Copper is long-proven and durable but costs more and takes longer to install. Most whole-house repipes today use PEX.

Can I stay in my house during a repipe?

Usually, yes. Many crews keep water on overnight and shut it off only during working hours. A typical single-family repipe takes a few days, plus time for drywall patching and the inspection.

Do I need a permit to repipe in Kent?

A repipe is a significant plumbing alteration, and cities generally require a plumbing permit and inspection for it. Make sure the quote states who pulls the permit, and confirm the company is a licensed plumbing contractor in L&I's Verify tool.

Phone line coming soon · Email us